Anthocyanin-fortified konjac glucomannan/sodium alginate composite edible boba: characteristics of texture,microstructure, in vitro release behaviour and antioxidant capacity

Konjac glucomannan/sodium alginate composite edible boba (KGM/SA-boba) with good taste is very popular in China, and it is an outstanding carrier for health potential ingredients. In this work, KGM/SA-boba were fortified with 0.25, 0.50, 0.75 and 1.00% purple sweet potato anthocyanin (PSPA), then characterised by the water distribution, texture, microstructure, in vitro release property of PSPA and antioxidant capacity. LF-NMR analysis demonstrated that the free water of KGM/SA-boba could transfer to tightly bound water with the addition of PSPA that made it with better water-binding ability, higher springiness and lower hardness. And the results of SEM and rheology showed that PSPA could stabilise the microstructure of KGM/SA-boba by forming more amorphous regions and hydrogen bonds proved by the results of DSC and FT-IR. Furthermore, 50% of PSPA in PSPA-fortified KGM/SA-boba can be released at the first hour in a simulated gastrointestinal environment. And the scavenging capacity of DPPH and ABTS of the PSPA-fortified KGM/SA-boba after digestion was higher than that of PSPA alone. Generally, PSPA could improve the texture while KGM/SA-boba in turn would make PSPA more stable in the gastrointestinal digestive system.     

Synthesis,microstructures, and corrosion behaviors of multi-components rare-earth silicates

Multi-components and equimolar rare earth monosilicates, (Y_1/3Dy_1/3Er_1/3)₂SiO₅, (Y_1/3Dy_1/3Lu_1/3)₂SiO₅, (Y_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅ and (Yb_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅, were prepared by solid-state reactions and the following hot-pressing. Dense microstructures with uniform elemental distributions were obtained for all samples. These investigated multi-components monosilicates exhibit low thermal conductivities and similar coefficients of thermal expansion with SiC. Moreover, they exhibit high corrosion resistances in 1400 °C water vapor, especially, four-components (Y_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅ and (Yb_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅ experienced almost invariable weights after small weight losses during the initial 0.5 h. All those results indicate that multi-components rare earth monosilicates are promising candidates of environmental barrier coatings for SiC/SiC composites.     

Synthesis and performance evaluation of a new drag reducer based on acrylamide/12-allyloxydodecyl acid sodium

Hydraulic fracturing with slickwater is a field-proven stimulation technology used in tight reservoirs. Because of the high pumping rate associated with slickwater fracturing, drag reduction (DR) is critical in minimizing pressure drop and the success of oilfield operations. In this paper, a new type of drag reducer (SPR) was synthesized with acrylamide and 12-allyloxydodecyl acid sodium, and its drag reduction performance was evaluated. The results showed that the new drag reducer features low molecular weight, fast-dissolving rate and low interfacial tension. The algorithm of estimating the drag reduction rate of non-Newtonian fluid SPR was proposed and validated. Empirical or semianalytical models for estimating the friction ratio (σ) or friction factor (λ or f) were used to simulate the turbulence behavior of the SPR drag reducer under different Reynolds numbers (Re). The modified Virk's correlation could accurately model the turbulent behavior of the SPR drag reducer. A unified calculation formula was established in this study for different pipe diameters.     

Preparation and characterization of calcium phosphate cement with enhanced tissue adhesion for bone defect repair

Anti-washout and tissue adhesion properties are essential for the clinical application of injectable bone materials. In this study, we prepared calcium phosphate cement (CPC) with anti-washout and tissue adhesion properties and attempted to build covalent bonds between CPC and the amino groups in bone tissue under a self-regulating pH system in the CPC (acidic to basic). The results of push-out tests demonstrated that a significant enhancement (from 6.42 ± 0.76 N to 61.5 ± 4.09 N) in tissue adhesion was obtained with the addition of 6% (w/w) oxidized sodium alginate (OSA) in CPC. The FTIR, XRD, anti-washout test, XPS, pH test, and SEM results suggested that the synergistic effect of OSA-citric acid (CA) led to the formation of a three-dimensional gel network structure in the CPC, and the Schiff base reaction between aldehyde and amino groups induced adhesion between CPC and the bone tissue. Further, the addition of less OSA had no significant negative effect on the hydration properties of CPC. Our work aims to promote the development of injectable bone material in clinical applications.     

Enhanced dielectric and piezoelectric properties in potassium sodium niobate/polyvinylidene fluoride composites using nano-silicon carbide as an additive

Piezoelectric materials are an indispensable part of modern life. Yet the existing environmental issues with conventional lead-based piezoelectrics has motivated scientist to develop novel substitutes including lead-free piezoelectric polymer composites. Following this path, the present research has focused on the fabrication of ternary composites of Polyvinylidene fluoride (PVDF)/Potassium Sodium Niobate (KNN)/nano-Silicon carbide (SiC) via hot compression molding and studying the effect of additives on the PVDF structure and the electrical properties of the composite. The obtained scanning electron micrographs and density measurements showed that the fabrication method provided dense samples. The activated polarization phenomena in the prepared samples enhanced dielectric permittivity and dielectric loss at a constant frequency with increasing KNN and SiC contents. Besides the expected dipole polarization, the presence of interfaces in the composites gave rise to the Maxwell–Wagner–Sillars effect and its corresponding polarization phenomenon. The semiconductive nature of SiC also promoted space charge polarization. However, these properties were frequency-dependent because the first two polarization mechanisms are deactivated at high frequencies. XRD patterns showed that SiC addition can alter the primary crystalline structure of PVDF and promote β-phase formation in the poled samples. Piezoelectric measurements confirmed the significant role of SiC addition to PVDF-KNN composites. The most significant increase in the piezoelectric properties was observed in PVDF-60KNN-1SiC, with a 183% increase in d₃₃ value. The PVDF-80KNN-1SiC had the highest d₃₃ value of 30.5 pC/N. It also had the best piezoelectric voltage coefficient and hence the highest figure of merit. Higher SiC contents restrict the efficiency of poling by forming a conductive path across the sample which would deteriorate the piezoelectric performance of the material. The present findings show that PVDF-KNN-SiC composites can be considered as a potential flexible piezoelectric material for future applications.     

蒸压建材生产过程中钢渣安定性处理与活性化利用

钢渣安定性处理过程常常造成胶凝活性的损失。为此，本文利用改性助剂消除钢渣水化过程中产生的氢氧化物并生成胶凝产物，在蒸压建材的生产过程中实现钢渣安定性处理和游离氧化物的活性化利用，并避免单独处置钢渣造成的活性物质损失。研究表明，8%秸秆灰和3%磷酸二氢铵作为复合助剂制备的尾矿-钢渣蒸压试块体积稳定，抗压强度达24.0MPa。通过对蒸压样品游离氧化物消解率、化学结合水量及热重、XRD分析，得出钢渣安定性处理与活性化利用机制：硅质材料与钢渣中f-CaO水化生成的Ca(OH)₂结合迅速生成对体系力学强度有益的水化硅酸钙，避免因大量Ca(OH)₂积累造成体积膨胀；磷酸盐中的NH₄⁺、H₂PO₄^-与f-MgO结合生成磷酸铵镁及其他低溶度积复盐类矿物，进而消除因f-MgO水化生成Mg(OH)₂造成体积膨胀的隐患。试样在180℃蒸压4h后，f-CaO及f-MgO消解率分别可达86.28%、89.73%。本文将为利用钢渣大比例取代水泥和石灰生产蒸压建筑材料提供理论基础，对于提高钢渣利用率、减少碳排放具有重要价值。     

Formulation strategy towards minimizing viscosity mediated negative food effect on disintegration and dissolution of immediate release tablets

Food induced viscosity can delay disintegration and subsequent release of API from solid dosage form which may lead to severe reduction in the bioavailability of BCS type III compounds. Formulations of such tablets need to be optimized in view of this postprandial viscosity factor. In this study, three super disintegrants, croscarmellose sodium (CCS), cross-linked polyvinylpolypyrrolidone (CPD), and sodium starch glycolate (SSG) were assessed for their efficiency under simulated fed state. Tablets containing these disintegrants were compressed at 10 and 30?KN, while taking lactose as a soluble filler. In addition to other compendial tests, disintegration force of these formulations was measured by texture analysis. Comparison of parameters derived from force – time curves revealed a direct relation of maximum disintegration force (F_max) and disintegration force development rate (DFDR) with compressional force in fasted state, whereas an inverse relationship of F_max and DFDR with compressional force was observed in fed state. The gelling tendency of disintegrants influenced the rate of release of API in simulated fed and fasted states when compressional force was changed. These observations recommend the evaluation of formulations in simulated fed state, in the development stage, with an objective of minimizing the negative impact of food induced viscosity on disintegration. Use of disintegrants that act without gelling or can counteract the effect of gelling is recommended for tablet formulations with reduced disintegration time (DT) and mean dissolution time (MDT) in fed state, respectively.     

Multi-Functional Black Bioactive Glasses Prepared via Containerless Melting Process for Tumor Therapy and Tissue Regeneration

Tissue regeneration in complex lesions such as the site of tumors, bacterial infection, and sites lacking blood vessels, has been a huge challenge. Therefore, developing bioactive implantable materials with multi-functional properties such as tumor destruction, bacteria growth inhibition, and angiogenesis promotion is of great significance. In this study, black CaO-SiO₂-TiO₂ (CST) glasses are prepared through the containerless melting approach, by which heterogeneous nucleation can be avoided and thereby glass formation becomes possible via fast quenching. This approach enables the formation of trivalent titanium (Ti³⁺) without using a reducing atmosphere or reducing agents. The black CST glasses are found in this study to possess a strong ability to inhibit bacteria and tumors by their excellent photothermal and photocatalytic effects. Strikingly, these glasses also promote the formation of blood vessels and accelerate the healing of chronic wounds by the synergistic effects of the photothermal effect and Si ions. Thus, this glass system can be a promising multi-functional material for tissue regeneration in complex lesions.     

Structural Aspects of P2-Type Na0.67Mn0.6Ni0.2Li0.2O2 (MNL) Stabilization by Lithium Defects as a Cathode Material for Sodium-Ion Batteries

A known strategy for improving the properties of layered oxide electrodes in sodium-ion batteries is the partial substitution of transition metals by Li. Herein, the role of Li as a defect and its impact on sodium storage in P2-Na_0.67Mn_0.6Ni_0.2Li_0.2O₂ is discussed. In tandem with electrochemical studies, the electronic and atomic structure are studied using solid-state NMR, operando XRD, and density functional theory (DFT). For the as-synthesized material, Li is located in comparable amounts within the sodium and the transition metal oxide (TMO) layers. Desodiation leads to a redistribution of Li ions within the crystal lattice. During charging, Li ions from the Na layer first migrate to the TMO layer before reversing their course at low Na contents. There is little change in the lattice parameters during charging/discharging, indicating stabilization of the P2 structure. This leads to a solid-solution type storage mechanism (sloping voltage profile) and hence excellent cycle life with a capacity of 110 mAh g^-1 after 100 cycles. In contrast, the Li-free compositions Na_0.67Mn_0.6Ni_0.4O₂ and Na_0.67Mn_0.8Ni_0.2O₂ show phase transitions and a stair-case voltage profile. The capacity is found to originate from mainly Ni³⁺/Ni⁴⁺ and O^2-/O^2-δ redox processes by DFT, although a small contribution from Mn⁴⁺/Mn⁵⁺ to the capacity cannot be excluded.     

Hot corrosion of TBC-coated components upon combustion of low-sulfur fuels

Gas turbine reliability is a crucial requirement for passenger safety in aviation and a secure energy supply. Hence, corrosive degradation of combustor parts, vanes, and blades in gas turbines must be prevented. One of the most severe forms of corrosion is alkali-sulfate-induced hot corrosion, which is associated with internal sulfidation of components and is usually anticipated to fade in importance in the absence of sulfur. However, the literature suggests that hot corrosion might still occur in low-sulfur combustion gases. In this study, established thermodynamic modeling methods are used to analyze the low-sulfur hot corrosion regime. Liquid sodium chromate is found to be stable in these conditions. A comparison of calculation results and engine findings suggests that high alkali levels can negatively impact thermal barrier coating life even if sulfur is absent in the fuel. Laboratory tests are carried out to validate the chromate formation on MCrAlY-coated specimens. It is shown that molten sodium chromate can alter the oxidation behavior of MCrAlY, promoting the formation of voluminous spinel. This represents a new and different form of hot corrosion compared to type I hot corrosion.